Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Just How to Install a Bathtub Yourself: Removing as well as Replacing.
Blog Article
What are your thoughts about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is readily available, the job can relocate easily; if you have to open a wall to remove the old tub as well as place the new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require an assistant to move out the old tub and set in the new one. Ensure you have qualified yourself for the job and fit trying it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to think about employing one before you start. Opportunities are you may require a specialist plumber to make tube links.
This post will help you mount a brand-new tub in your restroom if you have currently acquired a brand-new tub and do not require to alter the arrangement of your previous water supply pipelines.
Your devices and also material list must make up the following:
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water supply. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the remaining water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning during this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin making sure that the washing machines are in area between the faucet as well as the sink. Secure the tap in position with the manufacturer supplied backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical faucet connectors. The former kind should be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Utilizing both wooden boards under its feet, put the bath tub in the called for position. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to guarantee that the bath tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Turn on the water and inspect all joints as well as brand-new pipework for leakages and tighten them if required. Fill up the bath tub as well as also inspect the overflow electrical outlet and also the regular outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the tub needs to wait till the bathtub has been used a minimum of once as this will certainly resolve it right into its last setting.
Getting ready for the Setup
First of all, the supporting framework supplied with the bath should be fitted (if required) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to crack an inflexible seal, triggering the water to pass through the wall between the bathroom and the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, as well as can securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bathtub with water before securing, to allow for the activity experienced when the tub is in usage. The sealant can split fairly early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about Tools You Need to Install a New Bathtub , I assumed sharing that excerpt was smart. Enjoyed our content? Please share it. Let another person discover it. Thanks for going through it.
Instant Quote Report this page